Size of valve actuator60
Flange hole patternF0507
Swivel angle90 deg
End-position adjustment range at 0°-5 deg ... 5 deg
End-position adjustment range at nominal swivel angle-5 deg ... 5 deg
Shaft connection depth12 mm ... 19 mm
Fitting connection conforms to standardISO 5211
Mounting positionoptional
Mode of operationDouble-acting Single-acting
DesignRack and pinion
Closing directionCloses to the right Closes to the left
Symbol00991265 00991266
Valve connection conforms to standardVDI/VDE 3845 (NAMUR)
Connection point for positioner and position sensor conforms to standardVDI/VDE 3845 size AA 1
Burst pressure24 bar
Operating pressure29 psi ... 116 psi
Nominal operating pressure29 psi ... 87 psi
Maritime classificationSee certificate
CE mark (see declaration of conformity)To EU Explosion Protection Directive (ATEX)
UKCA marking (see declaration of conformity)To UK EX instructions
Explosion protection certification outside the EUEPL Db (GB) EPL Gb (GB)
Explosion protectionZone 1 (ATEX) Zone 1 (UKEX) Zone 2 (ATEX) Zone 21 (ATEX) Zone 21 (UKEX) Zone 22 (ATEX)
Certificate issuing authorityDNV TAP00001CE German Technical Control Board (TÜV) Rheinland 968/V 1106.01/2023
ATEX category gasII 2G
ATEX category dustII 2D
Explosion ignition protection type for gasEx h IIC T3 Gb X Ex h IIC T4 Gb X
Explosion ignition protection type for dustEx h IIIC T105°C Db X Ex h IIIC T175°C Db X
Explosion ambient temperature0°C <= Ta <= +150°C
Operating mediumCompressed air to ISO 8573-1:2010 [7:4:4]
Note on operating and pilot mediumDew point at least 10 °C below the ambient temperature and temperature of the medium Lubricated operation possible (in which case lubricated operation will always be required)
LABS (PWIS) conformityVDMA24364-B1/B2-L VDMA24364 zone III
Storage temperature-20 °C ... 60 °C
Ambient temperature-20 °C ... 150 °C
Torque at nominal operating pressure and 0° swivel angle14.7 Nm ... 63.3 Nm
Torque at nominal operating pressure and 90° swivel angle8.3 Nm ... 63.3 Nm
Note on torqueThe operating torque of the actuator must not be higher than the maximum permissible torque listed in ISO 5211, with reference to the size of the mounting flange and of the coupling.
Spring return torque at 0° swivel angle8.4 Nm ... 25.1 Nm
Spring return torque at 90° swivel angle14.7 Nm ... 44.2 Nm
Air consumption at 0.6 MPa (6 bar, 87 psi) per cycle 0°-nominal swivel angle-0°2 l ... 3.8 l
Product weight2793 g ... 3267 g
Shaft connectionT11 T14 T17
Pneumatic connectionG1/8 1/8 NPT
Note on materialsRoHS-compliant
Material sub-baseCoated wrought aluminium alloy
Material coverAnodised die-cast aluminium
Material sealsFPM NBR
Material springSpring steel
Material housingAnodised aluminium Aluminium, powder-coated
Material pistonDie-cast aluminium
Material bearingPOM PPS reinforced
Material camHigh-alloy stainless steel
Material screwsHigh-alloy stainless steel
Material shaftNickel-plated steel High-alloy stainless steel
.webp)
